Search
Close this search box.

Nord Three 1ET400A 4CH Power Amplifier

Starting from

£1,849.00

Nord Three 1ET400A 4CH Power Amplifier

Starting from

£1,849.00

The Nord Three 4CH is our entry level Purifi EIGENTAKT 1ET400A 4CH using 2 x  power supply. Consisting of amp module, PSU, Input buffer.

Using simplified input buffers (no Sparkos onboard regulators use supply from main PSU) with OPA1612 OP Amps. All buffers have 4 levels of On-Board Switchable Gain.

The 3CH can be upgraded to full MKII specification at a later date by purchasing REV D buffers.

Our Standard case is sourced from Italy and offers a consistent look across the range. We use quality RCA and XLR input sockets from Switchcraft in the USA and soldered directly onto buffer board no long input wire. Standard binding posts are 5 way including banana from CHK you will find these gracing the back of the £40K Ultima amplifiers.  The front main switch is finished in brushed stainless steel with an even blue halo LED. Our Nord badge is Aluminum and both this and the switch are neatly rebated. Which sits in our signature 3 parallel lines milled into the front of the case.  And they sit on solid brushed and polished lacquered isolation feet. Combined they produce a simple yet aesthetically pleasing look.

Moving inside the amplifier we build with a combination of quality and experience of laying out amplifiers in order to achieve ultimate performance. We balance this with ease of build in order to maintain lower prices without compromising quality. Vulnerable wire connections are double shrink sleeved to ensure long term reliability. We have recently moved to combine inputs directly to the buffer board eliminating long input signal paths.  Buffer boards are soldered using WBT silver solder. All resistors are either 1% or 0.1% tolerance where needed in the audio feedback path. Signal capacitors are ultra quite Wima Polypropylene while power caps are long life Panasonic FR range. Binding posts are connected to buffer board with as short a length of OFC Silver plated Teflon dielectric 14AWG wire. Neotech OCC option. The connections to the binding posts are crimped and soldered to ensure ultimate contact. Our SMPS have virtually zero noise emission’s an example of how this is achieved is attention to detail each power output transistor is individually wrapped in Copper foil shielding. We also pay a great deal of attention to Thermal testing when designing a new amp to ensure they run as cool as possible. Heat is the enemy and will reduce long term reliability.

All our amplifiers perform and offer far better value than any product available from dealers. Even our entry level MP range offer a base line of superb dynamics, amazing soundstage, clarity and sheer addictive musicality. Gone are any hints of the older Class D harsh and thin sound. They sound like the top notch Class A A/B amplifiers. Each amp is built by one individual who is responsible for its internal build quality.

There is no 40% dealer margin, no 40% distribution margin, no advertising or representatives supporting dealers to pay for. You buy direct from the us, the manufacture. We are free to source modules and parts from the very best (suppliers) in the world. Because of our low margins and overheads we can manufacture our amplifiers with the highest quality, expensive and  most reliable products available while keeping the cost low. It’s a winning formula and those that seek and take a leap of faith are truly rewarded with amazing sonic ability. We are passionate about our products and the way we look after you, in the highly unusual event of something going wrong. We loath the term (so called) Customer Service, we have all experienced that! What you get is to be treated as I would wish and expect to be – with directness and fairness, and I promise not to ask “Is their anything else I can help you with today”.

 

Weight14 kg
Dimensions54 × 50 × 20 cm

SPECIFICATION DIMENSIONS

• Standard 4CH Case

• 4 x Purifi 1ET400A Module

• 2 x Hypex SMPS1200A400 Power Supply

• 4 x Nord (cut down) REV C Buffer Board with OPA1612 Daul Op Amp

• Distortion: THD+N – – 0.001 % 20Hz

• Frequency Response: 0 – 50k Hz THD+N 100W – – 0.00017 % 20-20kHzHz

• Low Distortion: THD+N 100W – – 0.00017 % 20-20kHzHz

• SNR 131dB

• High Input Impedance 51K

• On-Board Switchable Gain 12.8-22.2-27.4-30.6 dB

• Ultra High Damping Factor

• High 25A Current Output Capable of driving 2ohm for the

Most Demanding of Speakers.

• Idle Loses  output Stage ~1.7W

• Efficiency >94%

450W 2ohm

425W 4ohm

227W 8ohm

• Frequency Response: 20 – 20kHz +/-.01dB

• Case mm W 450 D 410H 102

• Weight 14Kg

 

FEATURES & COMPONENTS

isolation feet 768x499 nord acoustic

UPGRADE OPTIONS

  • Stunning SE case option with ON OFF DIM LED
  • RCA Input
  • WBT 0703Cu Speaker Binding Posts
  • Neotech OCC 14AWG Solid Copper binding post internal wire

Automatically turn on amplifier when your 12V trigger equipped Preamp is turned on.

XLR fitted as standard add switchable RCA-XLR option.

Standard binding posts will accept bananas, spade and bare wire.

SpeakOn is a Pro audio speaker output connection require special speaker cables.

Standard wire is of very high quality OFC with Teflon dielectric. Upgrade to higher quality Neotech solid OCC if you believe in cables!

Upgrade to 5 year warranty. Covers parts and labour (Return delivery extra after 1 year)

Changes front panel to 4mm rackmount front and delete the aluminum feet with same look as standard front

nord amplifier neotech wire

NEOTECH UP-OCC SOLID COPPER 14AWG SPEAKER OUTPUT WIRE

Standard wire is of very high quality OFC with Teflon dielectric. Upgrade to higher quality Neotech solid OCC if you believe in cables!

Shopping Cart